雙組份打膠機是怎樣一種設備它對于廠房車間的環境到底有什么要求?不少人對它不是很了解。縱然是人士，對于打膠機的了解，實際上還只是停留在它的實際用途上。

　　What kind of equipment is it? What's the requirement for workshop environment? Many people don't know much about it. Even professionals, the understanding of the glue machine is actually just stuck in its actual use.

　　1、我們先說說對場地面積的要求，臥式打膠機不同于立式打膠機。立式打膠機對于廠房面積的要求比較高保守估計也要盡50平米的地方。

　　1, we first talk about the requirements of the site area, horizontal glue machine is different from the vertical rubber machine. Vertical glue machine for the factory area requirements are relatively high, conservative estimate also need to do 50 square meters of place.

　　而小型打膠機對于廠房面積的要求就要小很多了，僅僅需要不足10平米的地方就可以存放，主要的是由于設備體積小可以任意擺放，不需要專門為打膠機騰出空間來存放。

　　Small glue machine for plant area requirements will be much smaller, only less than 10 square meters of the place can be stored, the main equipment is due to small size can be arbitrarily placed, do not need to make room for gluing machine.

　　2、我們要說下打膠機對于地面平整度的要求，這個也是近期我廠參加北京玻璃展覽會是被問道多的問題。

　　2, we should say the ground sizing machine requirements for the ground roughness, this is our recent factory to participate in Beijing international glass exhibition is asked the most problem.

　　小型臥式打膠機對于地面的平整度要求不是非常高，設備在當初研發階段我們的工程師已經考慮到地面平整度的問題了所以在研發的過程中也著重的這個問題。

　　Small horizontal gluing machine for surface roughness requirements are not very high, in the initial stage of our equipment R & D engineers have taken into account the flatness of the ground problem so solving this problem is the focus in the process of research and development.

　　我們在設備當中專門增加了一個特殊裝置來地面不平整對打膠機打膠的影響。當然小編這也要強調一下雖然設備對地面的平整度要求不高，但是也不能滿地是坑坑洼洼的。

　　We have added a special device in the equipment to solve the impact of the ground roughness on the gluing machine. Of course this small would like to emphasize that although smooth equipment on the ground of requirements is not high, but not everywhere is bumpy.

　　打膠機對于廠房溫度、濕度的要求，作為設備來講打膠機本身對于廠房的溫度要求不高，一般應安裝在干燥、無粉塵、無腐蝕性氣體,溫度在0～40度的車間內。同其他設備的要求幾乎沒有什么太大的區別。

　　Gluing machine for workshop temperature and humidity requirements, as the equipment in terms of atx-ii itself for the workshop temperature is not high, the general should be installed in a dry, no dust, no corrosive gas, temperature 0 ~ 40 degrees in the workshop. There is little difference between the requirements of other equipment.

　　本文由雙組份打膠機為您提供，我們的網站是:http://www.kljgg.cn我們將以全心全意的熱情為您提供更的服務，歡迎您的訪問!

　　In this paper, a two component glue machine to provide you, our website is: http://www.kljgg.cn, we will wholeheartedly provide you with better service, you are welcome to visit!