丁基膠涂布機常見問題的方法：
The common problems of the butyl rubber coating machine are solved:
1.鋁框上出現一邊或兩邊都不沾膠的現象時
The phenomenon of no glue on either side or both sides of the 1. aluminum frame
我們應檢查膠缸、膠頭的溫度是否正常，壓力是否在我們?cè)O(shè)定的范圍之內，檢查兩膠頭的距離是否過大（此距離設定鋁條剛剛能從兩個打膠頭之間過去為好）。
We should check whether the temperature of the rubber cylinder and the rubber head is normal, whether the pressure is within our range, and check whether the distance between the two rubber heads is too large (the distance is set to the aluminum strip can just pass from the two rubber heads to the best).
如果上述情況都沒有問題，可斷定兩個打膠頭（或一個），由于丁基膠中有雜質而堵住了膠頭出膠的眼，這就需要卸下打膠頭，用煤油浸泡，然后將膠頭內的膠全部清理干凈后再裝上即可。
If the above conditions are all right, two glue heads (or one) can be determined. Because of the impurities in the butyl rubber, the gel head is blocked out, so we need to remove the rubber head and soak it in kerosene, then clean the glue in the adhesive head and then install it.
2.該設備全部采用液壓系統，油缸及液壓系統全部采用高壓油管連接，每個連接處都由組合墊密封，若發現漏油，及時更換組合墊。

2., the hydraulic system is used in all the devices. The oil cylinder and hydraulic system are all connected by high pressure oil pipe. Each connection is sealed by combination gaskets. If we find oil leakage, replace the combination cushion in time.
3.該設備的膠頭加熱和膠缸加熱，由加熱棒兩個和加熱盤一個提供，由溫控表來設定和調整溫度的高低，若發現溫度升不高或升高后往下降，請檢查加熱棒或加熱盤是否損壞，并檢查溫控表是否正常。
3. the equipment glue and glue cylinder head heating heating, the heating rod two and a heating plate, a temperature control table to set and adjust the temperature, if the temperature rise is not high or increased after going down, please check the heating rod or the heating disc is damaged, and check whether the normal temperature table.
客戶的滿意就是對我們的肯定，歡迎您前來選購我公司的產品，我們一直以為您提供產品為己任并一直堅持這樣做。歡迎您的光臨。
Customer satisfaction is our affirmation. You are welcome to purchase our company's products. We have always thought that you are responsible for products and have always insisted on doing so. Welcome to your visit.